• 注册
  • 可靠性试验 可靠性试验 关注:539 内容:3488

    关于voltage drop 测试

  • 查看作者
  • 打赏作者
  • 当前位置: 可靠性网 > 可靠性技术 > 可靠性试验 > 正文
  • 5
  • 可靠性试验
  • 我们公司是做传感器开关的,通用汽车客户要求我们做voltagedrop测试,我们都不明白这是什么测试下面是它的原文,哪位高手了解啊,请指点。
    [color=Red]4.1.1VoltageDrop.Voltagedropisameasureof
    thepowerandassociatedtemperatureriseacircuit
    isgeneratingasitpassescurrent.Voltagedropmeasurements
    conductedacrosscontactswhichhaveremained
    openforsustainedperiodswillbehigherthan
    measurementstakenafteroneortwocyclesofoperation.
    Forthisreason,startthevoltagedroptestby
    measuringcontactinterfaceswhichrequireactuation;
    thenreturntothecontactswhichmakecircuitinthe
    de-energizedstate.
    4.1.1.1Applythenominaltestspecificationoperating
    parameter(temperature,pressure,displacement,
    etc.)whichcausesaneiectricalcircuitchangeofstate
    tooccur.Maintaintheoperatingparameteruntilelectrical
    ormechanicalstabilityisachieved.
    4.1.1.2AKelvinorfour-wireapproachshallbeused
    toassuretheconnectorinterfaceisnotpartofthe
    recordedmeasurement.WhenaKelvinapproachis
    notpracticalduetodevicedesign,suchasinthecase
    ofskirtedorsealedswitches,voitagedropshallbe
    determinedbyplacingthevoltmeterprobesonthe
    femaleconnectorsoratapointontheharness75mm
    fromtheconnectorinterface.Noteanynon-Kelvin
    methodonthetestdatasheet.
    4.1.1.3Useananalogordigitalvoltmetercapableof
    0.001voltresolutionandapplytheratedresistiveload
    asdefinedbythetestspecification.Refertothecircuit
    schematicforterminalidentification;thencheckall
    contactinterfacesforallnormallyopenandnormally
    closedcircuits.
    4.1.1.4Takethevoltagedropmeasurements
    0.5to3.0saftertheloadcurrenthasstabilized.If
    readingisoutofspecificationlimits,repeatmeasurements
    threetimeswhileswitchingtheratedload
    andaveragereadingstoassurethevaluewillbe
    repeatablewhenreturnedtothedesignsource.Ifthe
    switchloadcurrentispulsingorintermittent,testata
    steadystateresistiveloadequaltothesteadystate
    applicationload..

    [[i]本帖最后由aitaitait于2008-12-1619:13编辑[/i]]

    Lv.2
    GMW3431里的测试条件. 你可以与通用汽车负责你们公司的试验验证工程师取得联系.争求他的意见! 并且某些电测试是系统测试,并不是单独针对某个元器件. 以下翻译的仅供参考. 4.1.1 压降是由于功率和温度上升导致引起的,温度上升是由于电流回路的热效应引起的。 在空置一段时间上测出的压降要大于运行过一两个周期的压降。 由于这个原因,先测试需要激励的接口的压降,然后再测试de-energized状态中回路 的接口。 4.1.1.1 采用测试规范参数的名义值(温度,压强,位移等等),这些参数可能导致回路状态 变化。保持运行参数直到达到机械或电子平衡。 4.1.1.2 用开式或四线方式来确定接头是否是纪录的测试方法。由于仪器设计的不同,比如一 个带有边缘的或者有密封的接头,开式方法不可用,可以用将电压计探针放在接头的另 一端或放在距离接头75mm的线束上的方法来测试压降。在测试记录单上记下非-开式方法。 4.1.1.3 利用一个精度在0.001伏特的电压计和测试规定的额定负载。端口定义参考示意图,在 接通和断开状态下检查所有的接口。 4.1.1.4 在负载电流稳定之后,测试压降0.5-3秒钟。如果读数超出了范围,重复测试三次,调 整额定功率何平均读数,当返回到设计来源时以保证数值可以重复。如果开关的负载电流使 脉冲式或间断的,用一个相等的稳定阻抗负载来测试。 [[i]本帖最后由dazz于2008-12-1716:56编辑[/i]]
    回复
    谢谢回复啊,真是好心人。 我们是GM代理商的供应商,没有办法直接与GM工程师联系的,只有和代理商联系,但代理商不太懂这个测试。
    回复
    Lv.2
    那就让代理商和GM工程师联系,也不能冒蒙做测试啊,呵呵
    回复
    Lv.2
    可以参看iec61000-4-11
    回复

    请登录之后再进行评论

    登录
  • 江苏拓米洛环境试验设备有限公司
  • 可靠性工程软件ReliaSoft中国总代理上海山外山机电
  • 上海红禾信息科技有限公司
  • 发布内容
  • 做任务
  • 动态
  • 风格
  • 到底部
  • 帖子间隔 侧栏位置: